How To Care For Your Cue Stick

The first thing you should do is invest in a case. This will protect the cue from humidity and falls or tip damage. Moisture is the biggest cause in your cue warping. Keep your cue away from moisture and very humid places. This minimizes the chances of your cue warping over time. Remember, however, that since wood is a natural material, there is no foolproof way to 100% guarantee you cue will not warp at all. They will all warp a little or more over time. A hard case is better than a soft case, and be sure to store your case upright. Now that it is safely stored in a protective case, remember to always wash your hands before you play and several hours after play.

Joint protectors should be considered if you are using a multi-piece cue. These will help to prevent moisture from entering by the shaft and butt of the cue. They screw into either end and will keep the moisture out and prevent warping. If by chance your cue does get warped, a slight warp is nothing to worry too much about. Just take caution when you play your game to position the cue the same for every shot. You want the warp on the vertical plane not the horizontal. The best way to check your cue for warping is by "sighting". Look straight down from the butt to the shaft, just as you would sight a rifle. The warp will be obvious, and you can then decide your positioning for your shots.

If you find the warp to be severe and are unable to bend it back into shape or cannot adjust your positioning, consider buying a new cue. Remember, investing in a case will save you these hassles down the road. After taking the precautions to avoid warping, turn your attention to the cue tip. The tip on your new cue may be shiny, smooth, and somewhat flat when you first get your cue. You may shape the tip to desired roundness, but many beginners just play with it the way it is. In either case, how you play and the way you stroke your cue will determine the final shape of your tip and constant shaping will wear your tip down very fast. There is an easy process for replacing tips if you find you need to do that. There are a few things you will need to have on hand before you begin. Make sure to have the new tip, a razor blade, glue, preferably SuperGlue Gel or Duro-gel, Loctite, 60-80 grip sandpaper, 400-600 grit sandpaper and some paper towels.

To start, remove what is left of the old tip using the razor blade. Be sure not to cut into the wood. Using the 60-80 grit sandpaper, sand the top of the ferrule (white plastic piece and the end of your cue, sometimes this is a brass piece). Then sand the bottom of the new tip with the same sandpaper until it is rough. Now that the tip and surfaces are prepared, you will attach the new tip. Apply a light coat of glue to both the ferrule and the bottom of the new tip. Only a small amount is needed on both pieces. Next, carefully center the tip onto the ferrule and hold in place for about a minute. When the glue has set, carefully use the razor to remove any excess over hang so the tip is flush with the ferrule.
To finish up, wet the sides of the tip slightly and burnish using the 400-600 sandpaper. You may also use the same paper to shape the tip to your desired radius. Allow the glue to dry completely before using for play. You're ready to go!
It is also important to keep your cue stick clean. After playing, you will notice a build-up of chalk on the tip. If you play using hand chalk, that will also be evident on the shaft. After play, it is a good idea to remember to always wipe down your stick. Any experienced billiard shooter will attest that nothing is worse and harms your shot more than a sticky cue shaft. There are several techniques that one can use to clean their pool cue shaft, ranging from a simply dry wipe-down, to and involved pool cue shaft smoothing and burnishing.

The buildup of sticky residue can accumulate over time if your pool cue shaft is not cleaned properly. You can help slow the buildup of sticky residue by always wiping the pool cue shaft down with a cotton cloth after play, as well as by doing the obvious; ensuring that you play with cleanly washed hands. You can also use a slightly damp cloth, but it is imperative that you completely and thoroughly dry the pool cue shaft immediately after wiping it clean to prevent warping.